User Tools
port_forwarding
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
| port_forwarding [01/30/2023 08:40] – [More Than One Node On Your Home Network] gfactor | port_forwarding [01/31/2023 05:40] – old revision restored (01/30/2023 18:11) gfactor | ||
|---|---|---|---|
| Line 36: | Line 36: | ||
| ===== More Than One Node On Your Home Network ===== | ===== More Than One Node On Your Home Network ===== | ||
| - | If you have more than one node on your network, then you’ll want to disable uPnP: | + | If you have more than one node on your network, then you’ll want to: |
| - | * Disable uPnP in the router (if it is a feature in your router and already enabled). | ||
| * Set a static IP address for each node in the router. | * Set a static IP address for each node in the router. | ||
| * Configure port forwarding in the router for each node. | * Configure port forwarding in the router for each node. | ||
| - | * Stop the core, then change the json settings on each node to disable uPnP. | + | * Stop the core, then change the json settings on each node to disable uPnP |
| * Start the core on each node. | * Start the core on each node. | ||
| - | 1) Login to your router | + | 1) Set the IP address of each node to STATIC. This will prevent the node’s IP address from changing |
| - | 2) Set the IP address of each node to STATIC. This will prevent the node’s IP address from changing and affecting all of this configuration. | + | 2) Set port forwarding for each node as shown in the following. Internal and external for each node will be unique and NOT match the other nodes: |
| - | + | ||
| - | 3) Set port forwarding for each node as shown in the following. Internal and external for each node will be unique and NOT match the other nodes: | + | |
| **Node 1** Internal: 12392 External: 12392 | **Node 1** Internal: 12392 External: 12392 | ||
| Line 62: | Line 59: | ||
| (Just change the last digit in each number.) | (Just change the last digit in each number.) | ||
| - | 4) Stop the core by entering the following command in the terminal: | + | 3) Stop the core by entering the following command in the terminal: |
| < | < | ||
| Open your settings.json - this may be blank which indicates you have the default settings. You will then copy and paste the code below into the settings.json and click save: | Open your settings.json - this may be blank which indicates you have the default settings. You will then copy and paste the code below into the settings.json and click save: | ||
| + | |||
| + | this would be for **Node 1** matching the port forwarding entry above: | ||
| < | < | ||
| " | " | ||
| " | " | ||
| + | }</ | ||
| + | |||
| + | this would be for **Node 2** matching the port forwarding entry above: | ||
| + | |||
| + | < | ||
| + | " | ||
| + | " | ||
| + | }</ | ||
| + | |||
| + | this would be for **Node 3** matching the port forwarding entry above: | ||
| + | |||
| + | < | ||
| + | " | ||
| + | " | ||
| + | }</ | ||
| + | |||
| + | this would be for **Node 4** matching the port forwarding entry above: | ||
| + | |||
| + | < | ||
| + | " | ||
| + | " | ||
| }</ | }</ | ||
port_forwarding.txt · Last modified: 06/17/2023 12:33 by crowetic