User Tools
port_forwarding
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
| port_forwarding [01/30/2023 14:37] – gisele_h | port_forwarding [01/31/2023 05:42] – gfactor | ||
|---|---|---|---|
| Line 9: | Line 9: | ||
| **Option 1:** In this case, you only have ONE device that is acting as a blockchain node for Qortal AND your router has uPnP enabled. The default settings that your node will have comes with uPnP enabled - uPnP is a feature that most common routers provide by default. If you are unsure, ask your service provider. With uPnP enabled in the router, and only ONE node running on your home network, you do NOT need to configure anything further on this guide. | **Option 1:** In this case, you only have ONE device that is acting as a blockchain node for Qortal AND your router has uPnP enabled. The default settings that your node will have comes with uPnP enabled - uPnP is a feature that most common routers provide by default. If you are unsure, ask your service provider. With uPnP enabled in the router, and only ONE node running on your home network, you do NOT need to configure anything further on this guide. | ||
| - | **Option 2:** If your router does NOT offer uPNP, you will need to port forward | + | **Option 2:** If your router does NOT offer uPNP, you will need to configure |
| - | 1) Stop the core: | + | 1) Stop the core on your node by opening the command terminal and entering: |
| < | < | ||
| - | 2) Open your settings.json | + | 2) Open your settings.json |
| < | < | ||
| " | " | ||
| Line 20: | Line 21: | ||
| } | } | ||
| </ | </ | ||
| - | |||
| - | If you have settings already displayed, look for the uPnPEnabled section, if it exists, simply replace ' | ||
| 3) Login to your router and set the IP address of the node to " | 3) Login to your router and set the IP address of the node to " | ||
| Line 32: | Line 31: | ||
| 5) Start your core: | 5) Start your core: | ||
| < | < | ||
| - | |||
| ===== More Than One Node On Your Home Network ===== | ===== More Than One Node On Your Home Network ===== | ||
| - | If you have more than one node on your network, then you’ll want to disable uPnP: | + | If you have more than one node on your network, then you’ll want to: |
| * Set a static IP address for each node in the router. | * Set a static IP address for each node in the router. | ||
| * Configure port forwarding in the router for each node. | * Configure port forwarding in the router for each node. | ||
| - | * Stop the core, then change the json settings on each node to disable uPnP. | + | * Stop the core, then change the json settings on each node to disable uPnP AND add the listenPort. |
| * Start the core on each node. | * Start the core on each node. | ||
| - | 1) Login to your router | + | 1) Set the IP address of each node to STATIC. This will prevent the node’s IP address from changing |
| - | 2) Set the IP address of each node to STATIC. This will prevent the node’s IP address from changing and affecting all of this configuration. | + | 2) Set port forwarding for each node as shown in the following. Internal and external for each node will be unique and NOT match the other nodes: |
| - | + | ||
| - | 3) Set port forwarding for each node as shown in the following. Internal and external for each node will be unique and NOT match the other nodes: | + | |
| **Node 1** Internal: 12392 External: 12392 | **Node 1** Internal: 12392 External: 12392 | ||
| Line 61: | Line 57: | ||
| (Just change the last digit in each number.) | (Just change the last digit in each number.) | ||
| - | 4) Stop the core by entering the following command in the terminal: | + | 3) Stop the core by entering the following command in the terminal: |
| < | < | ||
| Open your settings.json - this may be blank which indicates you have the default settings. You will then copy and paste the code below into the settings.json and click save: | Open your settings.json - this may be blank which indicates you have the default settings. You will then copy and paste the code below into the settings.json and click save: | ||
| + | |||
| + | this would be for **Node 1** matching the port forwarding entry above: | ||
| < | < | ||
| " | " | ||
| " | " | ||
| + | }</ | ||
| + | |||
| + | this would be for **Node 2** matching the port forwarding entry above: | ||
| + | |||
| + | < | ||
| + | " | ||
| + | " | ||
| + | }</ | ||
| + | |||
| + | this would be for **Node 3** matching the port forwarding entry above: | ||
| + | |||
| + | < | ||
| + | " | ||
| + | " | ||
| + | }</ | ||
| + | |||
| + | this would be for **Node 4** matching the port forwarding entry above: | ||
| + | |||
| + | < | ||
| + | " | ||
| + | " | ||
| }</ | }</ | ||
| Line 76: | Line 95: | ||
| 5) Start the core on each node: | 5) Start the core on each node: | ||
| < | < | ||
| + | |||
| =====Third Party Guides===== | =====Third Party Guides===== | ||
port_forwarding.txt · Last modified: 06/17/2023 12:33 by crowetic