Qortal Project

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Port Forwarding ======
{{:qortal_official_logo_transparent_.png?400|}}
 
Port forwarding can be necessary for helping your node stay synced and connected to peers.
This can increase connections/peers for your Qortal core node(s). We will try to make this scenario as simple as we can - as there are several variables. Choose the section below that fits your situation:

===== Single or Multiple nodes With uPnP Enabled=====

**Option 1:** If you have only ONE node, and your router has **uPnP enabled**, you will not need to do anything, your single node will simply start obtaining incoming connections. 

If you ARE going to use uPnP, **you can have MULTIPLE nodes** on the same LAN obtaining incoming connections **via uPnP** by simply modifying a SINGLE setting in **settings.json** for your SECOND node and HIGHER:

Simply edit **settings.json** for the nodes ASIDE FROM THE FIRST NODE, and change the listenPort for the subsequent nodes, below is an example for the second node on the LAN. 


<code>{
"listenPort": 22392
}</code>

=====Networks Without uPnP=====
On networks that do NOT have uPnP available, you will need to **enable port forwarding and static assignment** to obtain incoming connections. Doing this will be DIFFERENT on any given router. You will need to obtain instructions for your router from an internet search as far as the terminology and specific settings that you will need. 

We will provide **basic overall instructions** here for understanding.

1. Setup **static assignment** for each node machine on your LAN. - Static assignment ensures that the machine will obtain the **same LAN IP address** every time, from your router. (Some routers give static assignment other names, most of the time it will be located under **DHCP settings**.)

2. Establish a **port forwarding (or DNAT) entry** in your router, for each of your statically assigned node machines, changing the **external port** of each.

**You do NOT need to modify any further settings on your NODE**, simply add new entries for each node machine with a **DIFFERENT EXTERNAL PORT**. See below for an overall idea...

**Node 1** - Internal port: 12392, external port: 12392

**Node 2** - Internal port: 12392, external port: 22392

**Node 3** - Internal port: 12392, external port: 32392

etc... You can use ANY port you like for the different external port, as long as it **doesn't go over 65535** as that is the MAX port in the tcpv4 port range. Once you HAVE set different external ports for each, you can **check your external IP address** with a service like https://whatismyipaddress.com (look for ipv4 address there) and you will know what the peer address for Qortal will be for each of your nodes, with your external IP and whatever external port you set for each node.

**All that needs to change is the EXTERNAL port**, port forwarding will allow you to forward to the **SAME internal port on DIFFERENT IPs, this way no modifications of Qortal settings are required.** 


=====Third Party Guides=====

Here you can find step by step info for specific router: https://portforward.com/

Static IP guide: https://www.coolblue.nl/en/advice/assign-fixed-ip-address-router.html

Port forwarding guide: https://www.lifewire.com/how-to-port-forward-4163829


===== How to Port Forward with Advanced Settings =====

It is never a good idea to add your node in DMZ. That will stop all the DPI and SPI and if you have the API enabled and white listed, you are putting your computer at risk! DMZ bypasses the SPI mechanism of the built in filters and all the internet traffic can reach your node directly. SPI (stateful packet inspection) firewall protects you by examining incoming packets against existing connections.
Also add UPnP text. If a router has it then it must be enabled. UPnP or NAT-pmp opens dynamic port ranges to act as an assist for SPI. Enabling NAT/UPnP solves problem for the most but unfortunately due to the torrent p2p laws most ISPs now filter ports by default at the client side so port forward is also needed. For example:

219.88.183.49:12392 (qortal-1.2.3-2df0453), height 42318, sig: PXNoJM7W, ts 2020-07-31 17:17:24

192.168.100.83:44380 (qortal-1.2.3-2df0453), height 42318, sig: PXNoJM7W, ts 2020-07-31 17:17:24

Look at the second IP address with a dynamic port. This is UPnP working. Instead of 12392 , it has opened a 44380 port for TCP handshake / connect / ACK.
Qortal Project

User Tools

Site Tools

Page Tools
